QCX 5W CW transceiver kit (2024)

QCX: a feature-packed, high performance, single-band 5W CW transceiver kit, with WSPR beacon and built-in alignment/test equipment. Available for 80, 60, 40, 30, 20 or 17m bands. It has rotary encoder synthesised tuning, VFO A/B/Split, Iambic keyer, CW decoder, and more...

Click!Shop order $49

14-May-2020: The QCX kit has been replaced by the new QCX+ kit. Same circuit, same firmware, same functional operation - but physical improvements. See http://qrp-labs.com/qcxpfor details.

The "QCX" is a 5W, single-band, high performance CW transceiver kit with WSPR beacon, and built-in alignment/test equipment. It is available for 80, 60, 40, 30, 20 or 17m bands. See below for the long list of features! This is a kit of parts that you assemble yourself. There are NO surface mount components to solder (two SMD ICs are already factory pre-soldered).

Please see QCX Frequently Asked Questions page for any queries you have. In case of any problems, please see the QCX trouble-shooting page.

Features

Easy to build, single-board design, 10 x 8cm, all controls are board-mounted
Professional quality double-sided, through-hole plated, silk-screen printed PCB
Choice of single band, 80, 60, 40, 30, 20 or 17m
Approximately 3-5W CW output (depending on supply voltage)
7-16V recommended supply voltage
Class E power amplifier, transistors are bolted to the PCB as a heatsink, though heat dissipation is minimal
7-element Low Pass Filter ensures regulatory compliance
CW envelope shaping to remove key clicks
High performance receiver with at least 50dB of unwanted sideband cancellation
200Hz CW filter with no ringing
Si5351A Synthesized VFO with rotary encoder tuning
16 x 2 blue backlight LCD screen
Iambic keyer or straight key option included in the firmware
Simple Digital Signal Processing assisted CW decoder, displayed real-time on-screen
On-screen S-meter
Full or semi QSK operation using fast solid-state transmit/receive switching
Frequency presets, VFO A/B Split operation, RIT, configurable CW Offset
Configurable sidetone frequency and volume
Connectors: Power, 3.5mm keyer jack, 3.5mm stereo earphone jack, BNC RF output
Onboard microswitch can be used as a simple straight Morse key
Built-in test signal generator and alignment tools to complete simple set-up adjustments
Built-in test equipment: voltmeter, RF power meter, frequency counter, signal generator
Beacon mode, supporting automatic CW or WSPR operation
GPS interface for reference frequency calibration and time-keeping (for WSPR beacon)
CAT control serial data interface
Optional 50W PA kit

Assembly and operating instructions

The assembly document includes circuit diagram and a detailed description of transceiver operation. Please download the correct assembly instructions for your PCB revision. The PCB revision is the number in the bottom right corner.

NOTE: PCB Rev 4 kits shipped after 12-Apr-2019 have four component changes. Make sure you have the correct manual version. There are four component value changes in these kits shipped after 12-Apr-2019, which are explained on page 7 of the latest 1.12 manual dated 20-Apr-2019.

DOWNLOADS:

PCB Rev 5Manual CLICK HERE(document revision 1.21, 12-May-2020)
PCB Rev 4, Firmware 1.03 (kits shipped after 03-Dec-2019Manual CLICK HERE(document revision 1.16, 02-Jan-2020)
PCB Rev 4, Firmware 1.01 (kits shipped after 07-Oct-2019Manual CLICK HERE(document revision 1.13, 07-Oct-2019)
PCB Rev 4, kits shipped after 12-Apr-2019Manual A4 format, CLICK HERE(document revision 1.12, 20-Apr-2019)
PCB Rev 4Manual A4 format, CLICK HERE; for Letter paper, choose scale to fit page when printing (document revision 1.11, 31-Oct-2018)
PCB Rev 4ManualRUSSIAN, CLICK HERE- translation by Andrey R1CF (THANKS!) (revision 1.11a, 21-Jan-2019)
PCB Rev 4ManualJAPANESE, CLICK HERE- translation byShig JA1XRQ, see website here(THANKS!) (revision 1.11a, 05-Dec-2018)
PCB Rev 3Manual A4 format, CLICK HERE- for world except North America (document revision 1.10, 26-Jan-2018)
PCB Rev 3Manual Letter format, CLICK HERE- for North America (document revision 1.10, 26-Jan-2018)
PCB Rev 3ManualGERMAN, CLICK HERE- A4-format German translation contributed by Peter DL6DSA (THANKS!) (revision 1.10a, 10-Feb-2017)
PCB Rev 1/2Manual A4 format, CLICK HERE- for world except North America (document revision 1.08, 23-Oct-2017
PCB Rev 1/2Manual Letter format, CLICK HERE- for North America (document revision 1.08, 23-Oct-2017)
PCB Rev 1/2ManualGERMAN, CLICK HERE- A4-format German translation contributed by Peter DL6DSA (THANKS!) (revision 1.08, 23-Oct-2017)
PCB Rev 1/2 ManualJAPANESE3-parts:part-1part-2part-3translation of sections 1-4, contributed by Shig JA1XRQ (THANKS!) SeeShig's website for single doc(revision 1.08, 06-Nov-2017)
PCB Rev 4Hi-resolution (300dpi) circuit diagram/schematic, 4,375 x 2,279 pixels
PCB Rev 3Hi-resolution (300dpi) circuit diagram/schematic, 4,368 x 2,282 pixels

Firmware

There have been several firmware updates since the 21-Aug-2017 launch of this QCX CW transceiver kit. These provide enhancements and bug fixes. If you have an AVR programmer you can update your firmware using the on-board programming header.The firmware version history and more information are on this page (click!).

Operating manuals for firmware version 1.06 and above are a separate document and are also on the Firmware history page.

Modifications

CLICK HERE for a Modifications page, various improvements you can easily make to your QCX radio.

PCB Revisions

There have been a number of PCB revisions, these included minor changes which improved some aspect of the QCX orenabled new functionality.

Photographs

These photographs show the prototype kit, both with and without the LCD module plugged in. The powered-up kit shows the radio's Frequency Counter featuremeasuring the frequency generated by its Signal Generator feature.

Builders' enclosure photographs

A common question about the QCX transceiver, is about whatcase to use for it. There is not an official QRP Labs enclosure for the QCX. But many people are finding their own solutions to this question.

For photos and information about what some constructors have done about enclosing their QCX, visit theQCX builders' gallery page!

ARRL Review of QCX in August 2019 QST issue

Paul N1II reviewed the QCX transceiver in the August 2019 issue of the ARRL monthly publication QST. Quoted performance for QCX+ is expected to be equivalent to QCX, since there are no component changes and great attention has been given to PCB layout in both QCX and QCX+.

CLICK HERE to read the PDF(497K file)

Reproduced with the permission of the ARRL. Copyright ARRL.

Visit the ARRL website here.

Videos and reviews of QCX

Theoriginal QCX kit was originally designed for the RSGB Youths On The Air summer camp buildathon in August 2017. This RSGB YOTA Vlog video, shot at QRP Labs booth at Friedrichshafen 2017.

For more videos and reviews please see the QCX videos page!

K9YA Telegraph, March 2018 edition, review by Philip K9PL

The K9YA Telegraph's March issue has an article on the QCX by Philip K9PL, sub-titled "QRP Labs Moves the Goalposts". Philip concludes his 3-page article: "...the QCX behaves like a monoband, QRP slice out of a QRO high-end rig with deep, deep menus - very innovative and a joy to operate.

The K9YA Telegraph is a free monthly Ham Radio eZine, seehttp://www.k9ya.org/for details.

Philip K9PL has provided a PDF of the article with permission to reproduce it on the QRP Labs website. CLICK HERE to read it!

Common Issues

The following issues have arisen more than once, and have the solutions indicated.

Issue	Solution
Microprocessor does not boot up at power-up, requires switch-off/switch-on again to power up properly	See modification here
Power Amplifier instability results in low or unstable power output, or high current draw, or blown MPS2907	See modification here
LCD contrast fluctuates on transmit	Check for LCD module frame short to L2,see here for details
Low output power on 20m (or other band)	LPF inductance is probably too high, resulting in attenuation at the transmit frequency. Remove turns one at a time from LPF inductors L1, L2, L3
No power output at all	Check continuity through L1, L2, L3 and other inductors L4 and T1, as advised in the manual. Probably one or more have not properly burnt off the enamel so there is no electrical connection.

More troubleshooting

There is an extensive QCX troubleshooting guide, click here
An excellent article on troubleshooting 60 QCX-series kits, by Ron WA7GIL, see here
There is a detailed video aboutQCX troubleshooting, click here

Phase noise measurements

For a detailed page about phase noise measurement techniques and the measurements on the QCX in particular, CLICK HERE.

The transmitter output phase noise measured was within 1dB of the -135 dBc/Hz at 10 kHz and 50 kHz spacing measured by ARRL in their QST review (see above). This level is considered GOOD. No improvements were found to get better phase noise performance from the QCX.

Performance measurements by Ed WA4MZS

Ed made some interesting measurements of his 40m QCX serial number 354 (see also builders' photos page).

Power supply = 13.8 VDC
Current draw (receive) = 123 mA
Current draw (transmit) = 514 mA
Transmitter output (50Ω load) @ 7.020 MHz = 4.0 watts
Receiver MDS @ 7.020 MHz = -121 dBm (0.2 µV)
Reference frequency = 27.004345 MHz
Transmitter frequency (display 7.020 MHz) = 7.0200003 MHz
Transmitter 2nd harmonic (14.040 MHz) = -48.74 dBc

Spectrum analyser close-in and wide screenshots:

Board dimensions

The following diagram shows some dimensions of the QCX PCB. Important notes:

All dimensions indicated are in inches. Multiply by 25.4 to get mm
The PCB size is 4.0 x 3.2 inches exactly
The coordinates are indicated as X, Y in inches, relative to the 0, 0 origin which is the bottom left corner of the PCB
The coordinates of the gain potentiometer, tuning control, and the two buttons are all the center points of the control shafts
The coordinates of the PCB mounting holes in the corners are the center points of the drill holes
The coordinates of the BNC socket, 3.5mm jack sockets (audio out, paddle in), Power connector and microswitch (straight Morse key) are all the coordinates of the Eagle CAD library component origin, and are as shown by the end of the line mark on the diagram.
The coordinates of the LCD Module are the bottom left corner origin of the module, as shown. Please refer to the information on the LCD module below this diagram.

Specific notes about the LCD module:

The dimensions on this LCD module diagram (below) are in mm. Divide by 25.4 to get inches
The coordinates (in inches) of the LCD module in the above QCX PCB diagram refer to the bottom left hand corner of the LCD module
The LCD module is separated from the main QCX PCB in the vertical direction, by four 12mmnylonhex spacers installed at the corners
The LCD module PCB size is 80 x 36mm
The four corner holes are centered 2.5mm in from each corner of the LCD module
Do NOT trust the dimensions in the following diagram, for the HEIGHT of the module (cross-section at upper right of the diagram) and for the size of the black metal cover-plate for the LCD glass. These dimensions are known to vary slightly from manufacturer to manufacturer. So if you require exact measurements for these parameters you should verify them with your own measurements. The other dimensions (hole location, 80 x 36mm board size) are always standard.

QCX 3D model by Eugene UR5TLZ

SeeQCX 3D model page